How I painted my copy of the official 'Saboteur' model for the new game 1490 Doom.

Black Leather

1. Basecoat with Black .
2. Apply general highlights of Stegadon Scale Green .
3. Fine edge highlight everything, using Thunderhawk Blue .
4. Selectively highlight corners and curves with Fenrisian Grey .
5. Mix some White into your Fenrisian Grey then add a few specular highlights to corners.

Visor

1. Basecoat with Khorne Red .
2. Paint the majority of the visor with Evil Sunz Scarlet , leaving a little uncovered at the top and bottom, and roughly a quarter on each side. This is best applied as a couple of thin glazes, pulling your brush towards the centre.
3. Repeat a few times, mixing Ice Yellow into the Evil Sunz Scarlet . I covered roughly half, then increased the amount again, covering roughly a quarter.
4. Finish with a small highlight of pure Ice Yellow in the centre.

Black Armour and Cloth

1. Basecoat with Black .
2. Now with Eshin Grey , apply a chunky highlight down the most exposed parts, covering less area that the previous stage.
3. Add fine highlights using Dawnstone .
4. Selectively highlight with Administratum Grey .
5. Add a little White to the Administratum Grey and add a couple of specular highlights, where needed.

Arm Bindings

1. Basecoat with Steel Legion Drab .
2. Shade between the wrapping with thinned Rhinox Hide and a thin brush.
3. Glaze raised areas with Karak Stone , dragging your brush upwards.
4. Edge highlight wrappings with Ushabti Bone .
5. More selectively highlight with Screaming Skull .
6. Mix some :white into your Screaming Skull and highlight a little smaller.

Skin

1. Basecoat with Cadian Fleshtone .
2. Wash with 2:1 Reikland Fleshshade and Contrast Medium .
3. Selectively highlight with Kislev Flesh .
4. Finish with specular highlights of Pallid Wych Flesh .

Dirty Steel

1. Basecoat with Leadbelcher .
2. Wash with Basilicanum Grey .
3. Wash again, but with Agrax Earthshade this time.
4. Re-establish the basecoat with a drybrush of :Citadel/Leadbelcher.
5. Add rust into recesses, with a generous shade of thin Skrag Brown .
6. Enhance this in a few places with thin Balor Brown .Mix some Silver RLM01 Metallic into your Leadbelcher and pick out hard edges.
7. With pure Silver RLM01 Metallic , edge highlight the tip and place a few specular highlights on corners.

Dark Brown Leather

1. Basecoat with Rhinox Hide .
2. Take some thinned Mournfang Brown and apply a heavy glaze over the tube. Work in rough lines, always pulling your brush towards the apex of the tube.
3. Now with Skrag Brown , apply a chunky highlight down the most exposed part of the tube, covering less area that the previous stage.
4. Mix 1:1 Skrag Brown and Ushabti Bone and repeat the above, but make it a finer highlight.
5. Selectively highlight with Ushabti Bone .
6. Add a little White to the Ushabti Bone and add a couple of specular highlights, where needed.

Wood

1. Basecoat with Steel Legion Drab .
2. Wash with Agrax Earthshade .
3. Edge highlight/overbrush with Baneblade Brown .
4. More selectively edge highlight with Karak Stone .
5. Finish with small highlights of Karak Stone and White .

Steel

1. Basecoat with Leadbelcher .
2. Wash with Nuln Oil .
3. Glaze some Agrax Earthshade where you want metal to look dirtier.
4. Highlight with some Ironbreaker .
5. With pure Silver RLM01 Metallic , edge highlight the tip and place a few specular highlights on corners.

Brass/Bronze

1. Basecoat with Antique Gold or whatever brass/bronze paint you prefer.
2. Wash with Agrax Earthshade .
3. Add some Silver RLM01 Metallic to your basecoat, then edge highlight.
4. Finish with a few very small Silver RLM01 Metallic highlights.

Grey Cloth

1. Basecoat with Stormvermin Fur .
2. Wash with Nuln Oil .
3. Edge highlight with a 1:1 mix of Stormvermin Fur and Administratum Grey .
4. Finish with selective highlights of Administratum Grey and a little White .