Skin

1. Basecoat with 2:1 Deepkin Flesh and Stormvermin Fur .
2. Soft shade with 1:2 Deepkin Flesh and Stormvermin Fur .
3. Further define recesses with some thin Corvus Black .
4. Glaze highlight with Deepkin Flesh .
5. Add fine highlights with 1:1 Deepkin Flesh and Pallid Wych Flesh ,
6. Finish with selective highlights of Pallid Wych Flesh .

To a little warmth to areas, like the under eye-lids, apply glazes of Kislev Flesh . You can re-highlight with Pallid Wych Flesh , where needed too.

Eyes

1. Pick out eyeballs with Blue Horror .
2. Finish with a specular highlight of White in the centre.

Teeth

1. Pick out teeth with Wraithbone .
2. Finish with specular highlights of White on the points.

Tongue

1. Basecoat with 1:1 Black and Screamer Pink .
2. Glaze Screamer Pink towards the tip, on the top surface. Repeat as needed.
3. Add chunky highlights of 1:1 Screamer Pink and Pink Horror .
4. Add an edge highlight of Pink Horror .
5. Selectively highlight the tip with 1:1 Pink Horror and Kislev Flesh .
6. Finish with a specular highlight of Kislev Flesh on the tip.

Claws

1. Basecoat with Black .
2. Add highlights of Incubi Darkness .
3. Mix the Incubi Darkness 1:1 with Sybarite Green then run a line down the claws towards the tip.
4. Mix the above paint 1:1 with Wraithbone and selectively highlight.
5. Finish with specular Wraithbone highlights.

Fur

1. Basecoat with Black .
2. Pick out edges with Stormvermin Fur .
3. Selectively highlight with 1:1 Stormvermin Fur and Ushabti Bone .
4. Finish with specular highlights of Ushabti Bone .

Brown Leather

1. Basecoat with 1:1 Rhinox Hide and Mournfang Brown .
2. Mix the base colour 1:1 with Black , and use this colour to shade.
3. Add chunky highlights with a 1:1 mix of the original base colour and Gorthor Brown .
4. Apply finehighlights with pure Gorthor Brown .
5. Selectively highlight with Baneblade Brown ,
6. Finish with very small and specular highlights of 1:1 Gorthor Brown and Wraithbone .

Wrappings

1. Basecoat with Karak Stone .
2. Shade between bandages with thinned Steel Legion Drab .
3. Highlight with 1:1 Karak Stone and White .
4. Selectively highlight with 1:2 Karak Stone and White .

Bones (and Rope)

1. Basecoat with Ushabti Bone .
2. Wash with Skeleton Horde . You can probaly leave the ropes at this point, and just focus on the bones for the highlights.

Wood

1. Basecoat with Thondia Brown .
2. Run some thin Rhinox Hide into deep recesseswhere the wood meets other materials.
3. overbrush selectively with 2:1 with Thondia Brown and Steel Legion Drab . This is just to pick out the raised edges of the woodgrain, roughly.
4. Mix the previous paint 1:1 Administratum Grey and pick out where the recesses meet.

Canvas Bag

1. Basecoat with Baneblade Brown .
2. Add general shading with Steel Legion Drab .
3. Shade more selectively with 1:1 Steel Legion Drab and Rhinox Hide .
4. Add scratchy and chunky highlights of Karak Stone .
5. Repeat with fine highlights of Ushabti Bone .
6. Mix a little White into your Ushabti Bone and selectively highlight.

Rusty Steel

1. Basecoat with an equal parts mix of Black , Rhinox Hide and Abaddon Black
2. Stiple Typhus Corrosion on the part of the blade you want to be rusted.
3. Now thin down some Rhinox Hide , Mournfang Brown and Skrag Brown . Run this over the rusted area in patches, not being afraid of letting the paints mix. When this dries, it should give you a ice varied surface.
4. I then applied patches of Dirty Down Rust, using a damp brush. AGin, sticking to the rusted area.
5. Edge highlight the blade with Leadbelcher , making the highlights nice and chunky of the sharp edge of the blade.
6. Mix some Silver RLM01 Metallic into your Leadbelcher and edge highlight more selectively.
7. Finish with a few very small Silver RLM01 Metallic highlights.