Skin

1. Basecoat with 2 parts Administratum Grey , 2 parts Cadian Fleshtone and 1 part Blue Horror .
2. Wash with 2:1 Reikland Fleshshade and Contrast Medium .
3. Add a little Pallid Wych Flesh to your base colour and add chunky highlights.
4. Increase the amount of Pallid Wych Flesh in the mix and highlight more selectively.
5. Finish with very small/specular highlights of pure Pallid Wych Flesh .

Wood

1. Basecoat with Steel Legion Drab .
2. Wash with Agrax Earthshade .
3. Edge highlight/overbrush with Baneblade Brown .
4. More selectively edge highlight with Karak Stone .
5. Finish with small highlights of Karak Stone and White .

Fur

1. Basecoat with Stormvermin Fur .
2. Mix Stormvermin Fur and Rhinox Hide 1:1 then thin with an equal amount of water. Using this pretty thin paint, wash the fur.
3. Repeat, but this time with Nuln Oil , thinned with a medium of your choice. this step is just to add darkeness in the very deepest parts.
4. Re-establish Stormvermin Fur on edges. I did this with a rough overbrush, mostly.
5. Selectively highlight points and corners with 1:1 Stormvermin Fur and Ushabti Bone .
6. Finish with specular highlights of Ushabti Bone .

Khaki Cloth

1. Basecoat with Tallarn Sand .
2. Wash with 1:1 Tallarn Sand and Rhinox Hide , thinned with an equal amount of water.
3. Enhance shading in deep parts and where the cloth meets other materials with thin lines of Rhinox Hide .
4. Re-establish Tallarn Sand on folds, where needed.
5. Apply fine edge highlights of 1:1 Tallarn Sand and Screaming Skull .
6. Finish with small highlights of Screaming Skull and specular ones of Wraithbone .

Grey Cloth

1. Basecoat with Stormvermin Fur .
2. Shade recesses with a mix of 2 parts Stormvermin Fur , 2 parts Abaddon Black and 1 part Incubi Darkness .
3. Edge highlight with 1:1 Stormvermin Fur and Administratum Grey .
4. Selectively edge highlight with Administratum Grey and a little White .

Black Leather

1. Basecoat with Black .
2. Apply general highlights of Stegadon Scale Green .
3. Fine edge highlight everything, using Thunderhawk Blue .
4. Selectively highlight corners and curves with Fenrisian Grey .
5. Mix some White into your Fenrisian Grey then add a few specular highlights to corners.

Dark Brown Leather

1. Basecoat with Rhinox Hide .
2. Take some thinned Mournfang Brown and apply a heavy glaze over the leather. You are looking to cover pretty much everything but the recesses here.
3. Now with Skrag Brown , apply a chunky highlight down the most exposed parts, covering less area that the previous stage.
4. Mix 1:1 Skrag Brown and Ushabti Bone and repeat the above, but make it a finer highlight.
5. Selectively highlight with Ushabti Bone .
6. Add a little White to the Ushabti Bone and add a couple of specular highlights, where needed.

Bandages

1. Basecoat with Steel Legion Drab .
2. Shade between the wrapping with thinned Rhinox Hide and a thin brush.
3. Glaze raised areas with Karak Stone , dragging your brush upwards.
4. Edge highlight wrappings with Ushabti Bone .
5. More selectively highlight with Screaming Skull .
6. Mix some White into your Screaming Skull and highlight a little smaller.

Steel

1. Basecoat with Leadbelcher .
2. Wash with Basilicanum Grey .
3. Wash again, but with Agrax Earthshade this time.
4. Re-establish the basecoat with a drybrush of :Citadel/Leadbelcher.
5. Add rust into recesses, with a generous shade of thin Skrag Brown .
6. Enhance this in a few places with thin Balor Brown .Mix some Silver RLM01 Metallic into your Leadbelcher and pick out hard edges.
7. Selectively highlight with pure Silver RLM01 Metallic where the light would really hit.